Ten-tec Centurion Amplifier Model 422 For Omni-vii Omni-vi Plus Paragon Eagle
TEN-TEC CENTURION MODEL 422 1300 Watt 160-10 Meter 3-500Z Linear Amplifier. Excellent working condition with strong Eimac 3-500Z Tubes.
Has the following brand new parts, Peter Dahl Transformer, All High Voltage Rectifier Diodes and Filter Capacitors. Wired for 220-240VAC and should only be used on 220-240 VAC.
Has Factory 10/15 meter module. Rated output by Ten-Tec is 1300 Watts. Looks very good but has a few light scratches on cabinet top. LP 100 Wattmeter shown in pictures for demonstration only and not included with Ten-Tec 422 Amplifier sale. Band Coverage: 1.8 - 2.0, 3.2 - 4.7, 6.5 - 10.3, 13.4 - 19.6, 17.6 - 21.5. 21.5 - 29.7. Input Power: 2000 watts, maximum. Power Output: 1300 watts SSB, 1000 watts CW, RTTY and SSTV 650 watts, 50% duty cycle. Drive Power: 100 watts for full rated output. Efficiency: 50 - 65%, depending on frequency and load impedance. Input/Output Impedances: 50 Ohms, unbalanced, SWR. Distortion: -35 dB from 1 kw RF output level. CW Break-in: QSK capable, Relay switching.
Tube Complement: Two Eimac 3-500Z. Power Amplifier Circuit: Class AB2, grounded grid. Plate Voltage: 3100 volts, no load. Cooling: Forced air with full chassis air flow. Metering: Dedicated plate current meter.
Selectable multi-meter for plate voltage, grid current, forward or reflected power. Ten element LED bargraph display for peak power indication. Front Panel Status Indicators: Standby, operator, transmit. For full power operation, 220 - 250 VAC strongly recommended. Circuit Protection: Primary line fuses.
Plate transformer primary interlock and high voltage shorting bar. Front Panel Controls: Power on/off, standby/operate, control mode select (QSK - PTT/VOX), plate TUNE and LOAD, band switch, meter switch. Tune and Load Controls: 6:1 vernier drives with calibrated dial skirts. Construction: Aluminum chassis, front and rear panels, interior partitions and top and bottom covers. Size: HWD 8.25" x 15.25" x 18.5 (20.3 x 38.7 x 46.9 cm). Weight: 47 lbs (21.3 kg). Note for older 422 Centurion amp owners: Using an older Centurion with the newest Ten-Tec HF transceivers - Pegasus, Jupiter, and Orion - may require a small modification to the QSK board in older Centurion amps for proper QSK CW keying. Short diode D2 (red diode, 1N4148, next to Q1) with a jumper wire. The current 422B does not require this modification. The item "TEN-TEC CENTURION AMPLIFIER MODEL 422 FOR OMNI-VII OMNI-VI PLUS PARAGON EAGLE" is in sale since Sunday, February 2, 2020. This item is in the category "Consumer Electronics\Radio Communication\Ham, Amateur Radio\Ham Radio Amplifiers". The seller is "zrcatman" and is located in Colgate, Wisconsin.
This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Bermuda, Luxembourg, Paraguay, Reunion, Uruguay. Output Power: 1300 W
Supported Modes: CW
MPN: Does Not Apply