3000 watts RMS amplifier for 1.8 to 30 MHz HF linear 50v LDMOS BLF188XR 10 meter

  

3000 watts RMS (or Average or Bird watts), 4000+ watts PEP, 4x BLF188XR, front gain control and SSB switch, internal relay to turn off bias when stand by to reduce heating. 50 watts RMS max input (I can adjust this to any requirement, example 100, 10, 25 watts, etc). Requires 50 volts and 100 amperes power supply and 12 volts for bias, relays and fan. This is not a 12 volts amplifier. This sale is for the amplifier only, any other items on the pictures are not included. Amplifier approximate case measurements: 14 1/4" x 13 1/2" x 5 1/4 not counting the front switches, cables or back connectors. All measurements are done using Bird 43 wattmeters, RMS readings are measured with dead key with the PEP kit turned off, PEP readings are measured modulated and the PEP kit turned on. We measured the harmonics using a Bird Signal Hawk spectrum analyzer. Other measurements are done with a Fluke scopemeter/oscilloscope. All wattage measurements are off the air using a CDI 50 ohms 10kw terminating load (dummy load). Bird 43 measuring the output power, PEP kit off, 1x multiplier with a 5000 watts slug, 50 scale in the meter. Good ventilation, cool room temperature, 50 volts power supply with 100 amperes, ammeter and 12 volts power supply are required to operate this amplifier. You fail to do this, the amplifier dies, you decide. BLF188XR transistor is RUGGED, but that doesn't mean it will not fail, you can literally cut the antenna cable and it will not die, but you go more than 90 amperes (this amplifier with 4 BLF188XR), you will have shooting stars, please don't try cutting the antenna cable..... DO NOT OVERDRIVE THE AMPLIFIER.

As a reminder, please don't overdrive the amplifier. Don't forget to use a Low Pass Filter on Ham radio bands, don't forget to NOT OVERDRIVE THE AMPLIFIER and the good ventilation with cool room temperature is very important, if you left your amplifier to melt itself like a Chernobyl reactor it's your fault, you been warned.

Please make sure you follow all FCC rules, this amplifier is not intended to be used on Citizen Band (CB), to be used without a low pass filter in the Ham bands(160-6 meters), to use it with more than 1500 watts in the HAM bands or to use it in digital mode. The power output of this amplifier will vary depending your radio, antenna, frequency, coax, SWR and any other circumstances.

I will continue to improve the amplifier so maybe the pictures are outdated. The item "3000 watts RMS amplifier for 1.8 to 30 MHz HF linear 50v LDMOS BLF188XR 10 meter" is in sale since Tuesday, July 7, 2020. This item is in the category "Consumer Electronics\Radio Communication\Ham, Amateur Radio\Ham Radio Amplifiers".turbo" and is located in Boynton Beach, Florida. This item can be shipped to United States, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Panama, Jamaica, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Viet nam, Uruguay.

• Model: 3
• Country/Region of Manufacture: United States
• Band: HF
• Type: Linear Amplifier
• Supported Modes: AM
• Year Manufactured: 2020
• MPN: Does Not Apply
• Power: 3000w
• Brand: vijovame
• Manufacturer Warranty: None